Ultrasensitive and ultrastretchable metal crack strain sensor based on helical polydimethylsiloxane

• Shangbi Chen,
• Dewen Liu,
• Weiwei Chen,
• Huajiang Chen,
• Jiawei Li and
• Jinfang Wang

Beilstein J. Nanotechnol. 2024, 15, 270–278, doi:10.3762/bjnano.15.25

• %. Similarly, Kim et al. propose an approach incorporating a superaligned carbon nanotube sheet between a sensory metal film and an elastomer substrate, resulting in excellent and well-balanced strain sensing performance [26]. This characteristic imparts significant stretchability (ε = 100%) to the Pt crack

Experimental investigation of usage of POE lubricants with Al₂O₃, graphene or CNT nanoparticles in a refrigeration compressor

• Kayhan Dağıdır and
• Kemal Bilen

Beilstein J. Nanotechnol. 2023, 14, 1041–1058, doi:10.3762/bjnano.14.86

• to the fact that heat transfer is fundamentally a surface-related process [5]. Nanolubricants have been widely used in recent years to improve the performance of refrigeration compressors [6][7][8]. Singh et al. [9] experimentally verified the effect of addition of multiwalled carbon nanotube (MWCNT

Biomimetics on the micro- and nanoscale – The 25th anniversary of the lotus effect

• Matthias Mail,
• Kerstin Koch,
• Thomas Speck,
• William M. Megill and
• Stanislav N. Gorb

Beilstein J. Nanotechnol. 2023, 14, 850–856, doi:10.3762/bjnano.14.69

• dehumidifiers or water purifiers. The authors here present a model based on a carbon nanotube structure that might finally provide a route to the breakthrough in this field. Their archetype, the Namibian desert beetle, uses a geometric separation of hydrophilic and hydrophobic regions to harvest and drive water

• along its body. The authors built on this inspiration to develop carbon nanotube cones which similarly separate the regions. Their model predicts the specific geometry and surface properties that will be required to create a low-pressure system for harvesting water vapour. Rebora et al. [19], in the

Carbon nanotube-cellulose ink for rapid solvent identification

• Tiago Amarante,
• Thiago H. R. Cunha,
• Claudio Laudares,
• Ana P. M. Barboza,
• Ana Carolina dos Santos,
• Cíntia L. Pereira,
• Vinicius Ornelas,
• Bernardo R. A. Neves,
• André S. Ferlauto and
• Rodrigo G. Lacerda

Beilstein J. Nanotechnol. 2023, 14, 535–543, doi:10.3762/bjnano.14.44

• devices that can be easily fabricated by scalable printing techniques. We monitored the electrical response due to the interaction between a given liquid with the carbon nanotube–cellulose film over time. Using principal component analysis of the electrical response, we were able to extract robust data to

• rapid, inexpensive, and robust liquid analysis and identification. Keywords: carbon nanotube; electronic tongue; fibrillated cellulose; liquid sensor; Introduction The development of a new generation of smart sensors that allow for the monitoring of industrial processes in real time and for wearable

• sensing, as electromagnetic shielding, and as thermoelectric material [32][33][34][35][36][37][38]. Also, Qi et al. reported a liquid-water sensor based on carbon nanotube–cellulose composite films, and, more recently, Goodman et al. reported the scalable manufacturing of nanocomposites for liquid sensing

Single-step extraction of small-diameter single-walled carbon nanotubes in the presence of riboflavin

• Polina M. Kalachikova,
• Anastasia E. Goldt,
• Eldar M. Khabushev,
• Timofei V. Eremin,
• Timofei S. Zatsepin,
• Elena D. Obraztsova,
• Konstantin V. Larionov,
• Liubov Yu. Antipina,
• Pavel B. Sorokin and
• Albert G. Nasibulin

Beilstein J. Nanotechnol. 2022, 13, 1564–1571, doi:10.3762/bjnano.13.130

• carbon nanotube geometries remain one of the paramount technological challenges for their potential applications [2][5][8][9][10]. The noncovalent functionalization of carbon nanotubes promotes their individualization due to hydrophobic interactions between nanotubes and surfactant molecules that also

Studies of probe tip materials by atomic force microscopy: a review

• Ke Xu and
• Yuzhe Liu

Beilstein J. Nanotechnol. 2022, 13, 1256–1267, doi:10.3762/bjnano.13.104

• factor in determining the resolution of microscopy, and the performance of probes varies in various modes and application requirements. This paper reviews the latest research results in metal, carbon nanotube, and colloidal probes and reviews their related methods and techniques, analyses the advantages

• the direction of new probes and further promotes the broader and deeper application of scanning probe microscope (SPM). Keywords: AFM; carbon nanotube probe; colloid probe; metal probe; Introduction AFM represents a well-established technique for the investigation of the nanosurface morphology

• shown to be removed one by one from the sample surface by tip indentation of the scanning tunneling microscope (STM). The probing of the interaction forces by AFM and thus the analysis of van der Waals (vdW) forces can provide valuable information on the evolution of the tip size. Carbon nanotube probes

Application of nanoarchitectonics in moist-electric generation

• Jia-Cheng Feng and
• Hong Xia

Beilstein J. Nanotechnol. 2022, 13, 1185–1200, doi:10.3762/bjnano.13.99

• generate an electrical signal up to 10 mV and successfully applied it to a flow sensor. In 2008, Zhao et al. prepared a single-walled carbon nanotube generator [7], which imparted momentum to the water in the carbon nanotubes by applying a voltage to both ends of the carbon nanotubes, such that the other

• part of the single-walled carbon nanotube generated a millivolt-level voltage and nanoampere-level current (Figure 1a). These early confirmatory studies demonstrate that the liquid flow potential can be harnessed to generate electrical energy (Figure 1c,d). They also play a basic role in further

• microscopy (SEM) image of an individual single-walled carbon nanotube (SWNT) device. (c) Dependence of the induced voltage difference, ΔV, on the quantity of water injected into the chamber. ΔV increases with the quantity of water inside the chamber and tends to saturate at 500 μL. It is nearly symmetric for

Biomimetic chitosan with biocomposite nanomaterials for bone tissue repair and regeneration

• Se-Kwon Kim,
• Sesha Subramanian Murugan,
• Pandurang Appana Dalavi,
• Sebanti Gupta,
• Sukumaran Anil,
• Gi Hun Seong and
• Jayachandran Venkatesan

Beilstein J. Nanotechnol. 2022, 13, 1051–1067, doi:10.3762/bjnano.13.92

• tissue engineering Chitosan–carbon nanotube composites Carbon nanotubes have distinct physical, chemical, and optical properties that enable new bioengineering applications, notably in the development of natural bone tissue repair and replacement scaffolds. Carbon nanoparticles can provide a chemically

• -hydroxybutyrate) chitosan/multiwalled carbon nanotube scaffold coated with a nanobioglass–titania scaffold on bone cell regeneration was investigated. Scanning electron microscopy (SEM) examination verified the porosity of the scaffolds in the 300–700 µm range. The incorporation of chitosan into poly(3

• /functionalized multiwalled carbon nanotube/chitosan/hydroxyapatite composite were described in a bone tissue engineering application study. The XRD patterns of the lyophilized scaffolds reveal the presence of collagen, chitosan, and hydroxyapatite at 20°, 31.9°, 26.5°, 32.3°, 34.2°, 40.8°, and 75.6°. The

Electrostatic pull-in application in flexible devices: A review

• Teng Cai,
• Yuming Fang,
• Yingli Fang,
• Ruozhou Li,
• Ying Yu and
• Mingyang Huang

Beilstein J. Nanotechnol. 2022, 13, 390–403, doi:10.3762/bjnano.13.32

• , Kaul et al. [15][16] prepared a two-terminal SWCNT NEM switch. The response time of the switch is nanoseconds, and the voltage is 3.5–4.5 V. Cha et al. [21] prepared a multiwalled carbon nanotube (MWCNT) NEM switch. The switch length is 800 nm, the diameter is 20–40 nm, the initial gap is 40–60 nm, and

• coating to disperse carbon nanotubes on a substrate by coating with a solution carbon nanotube powder in dichlorobenzene. In addition, a more general solution deposition process is AC dielectrophoretic technology [2][23]. The dielectrophoretic technology requires low voltage, high frequency, and can

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

Impact of electron–phonon coupling on electron transport through T-shaped arrangements of quantum dots in the Kondo regime

• Patryk Florków and
• Stanisław Lipiński

Beilstein J. Nanotechnol. 2021, 12, 1209–1225, doi:10.3762/bjnano.12.89

• in the linear conductance [23][24][27][28]. There are also reports on T-shaped carbon nanotube structures [29][30] and similar carbon devices engineered by attaching C60 buckyballs onto the sidewall of a single-walled carbon nanotube (carbon nanobud [31]). Many experiments showed that Kondo and Fano

• strength depend on the specific setup. All ranges, that is, weak, intermediate, and strong coupling, are accessible. As an example, data for carbon systems are given: The experimental results for suspended carbon nanotube QDs showed an average value of strong coupling λ ≈ 1.7 [48]. For fullerene C60

Progress and innovation of nanostructured sulfur cathodes and metal-free anodes for room-temperature Na–S batteries

• Marina Tabuyo-Martínez,
• Bernd Wicklein and
• Pilar Aranda

Beilstein J. Nanotechnol. 2021, 12, 995–1020, doi:10.3762/bjnano.12.75

• combining the active material with free-standing, cloth-type carbonaceous materials. For instance, Yu et al. [22] reported the development of a cathode based on a sodium polysulfide catholyte soaked into a multiwall carbon nanotube (MWCNT) fabric. The resulting fabric/Na2S6 cathode exhibited higher capacity

Paper-based triboelectric nanogenerators and their applications: a review

• Jing Han,
• Nuo Xu,
• Yuchen Liang,
• Mei Ding,
• Junyi Zhai,
• Qijun Sun and
• Zhong Lin Wang

Beilstein J. Nanotechnol. 2021, 12, 151–171, doi:10.3762/bjnano.12.12

• ., metal nanowires, conducting polymers, carbon nanotube (CNT) inks, multiwall carbon nanotube (MWCNT) inks, and reduced graphene oxide) [69][70][71][72][73][74][75][76][77][78][79][80][81][82], can be easily absorbed or used as a coating layer on the surface of the paper due to its wettability and

Kondo effects in small-bandgap carbon nanotube quantum dots

• Patryk Florków,
• Damian Krychowski and
• Stanisław Lipiński

Beilstein J. Nanotechnol. 2020, 11, 1873–1890, doi:10.3762/bjnano.11.169

• Patryk Florkow Damian Krychowski Stanislaw Lipinski Department of Theory of Nanostructures, Institute of Molecular Physics, Polish Academy of Sciences, M. Smoluchowskiego 17,60-179 Poznań, Poland 10.3762/bjnano.11.169 Abstract We study the magnetoconductance of small-bandgap carbon nanotube

• single-walled carbon nanotube is a hollow cylinder formed of graphene. A CNT can be either metallic or semiconducting, depending on the way graphene is rolled up [37][38]. In the simple “zone folding” picture [39][40], the band structure of CNTs is obtained from the band structure of graphene by imposing

• analysis we consider the low-energy and low-temperature ranges. Therefore, we restrict most parts of our discussion to only a single shell of carbon nanotube energy states, that is, to four states labeled by spin (s = ±1) and valley pseudospin (l = ±1). The model we use to describe carbon nanotube quantum

Towards 3D self-assembled rolled multiwall carbon nanotube structures by spontaneous peel off

• Jonathan Quinson

Beilstein J. Nanotechnol. 2020, 11, 1865–1872, doi:10.3762/bjnano.11.168

• individual nanomaterials can be a challenging task. However, it opens up opportunities for the production of increasingly complex nanostructures. Unusual rolled multiwall carbon nanotube structures are synthesized here by simply inducing a change of precursor composition during the growth of multiwall carbon

• nanotube forests. The multiwall carbon nanotube structures are comprised of nitrogen-doped and undoped sections, and are obtained via a detailed peel off and roll mechanism. These results open new doors for the development of increasingly complex nanostructures. Keywords: chemical vapor deposition

Vibration analysis and pull-in instability behavior in a multiwalled piezoelectric nanosensor with fluid flow conveyance

• Sayyid H. Hashemi Kachapi

Beilstein J. Nanotechnol. 2020, 11, 1072–1081, doi:10.3762/bjnano.11.92

• a modified strain gradient theory (MSGT) and Gurtin–Murdoch surface elasticity to investigate the size-dependent nonlinear pull-in instability [28]. A new size-dependent nonlinear model for the analysis of the behavior of carbon nanotube resonators was introduced by Farokhi et al. based on modified

• /interface effects, the pull-in voltage and critical fluid velocity reach zero later than the rest of the parameters. Fluid-conveying multiwalled piezoelectric nanosensor. (a) Illustration of van der Walls forces between two adjacent tubes of a multiple shell cross section of a multiwalled carbon nanotube

Nickel nanoparticles supported on a covalent triazine framework as electrocatalyst for oxygen evolution reaction and oxygen reduction reactions

• Secil Öztürk,
• Yu-Xuan Xiao,
• Dennis Dietrich,
• Beatriz Giesen,
• Juri Barthel,
• Jie Ying,
• Xiao-Yu Yang and
• Christoph Janiak

Beilstein J. Nanotechnol. 2020, 11, 770–781, doi:10.3762/bjnano.11.62

• than N-doped carbon sheets requiring 0.41 V vs RHE [58] and better performance than nitrogen-doped graphene/carbon nanotube hybrids requiring an overpotential of 0.4 V vs RHE at 10 mA/cm2 [59]. In comparison with the literature, CTF-1-600 and Ni/CTF-1-600-22 appear to be highly active OER

Synthesis and enhanced photocatalytic performance of 0D/2D CuO/tourmaline composite photocatalysts

• Changqiang Yu,
• Min Wen,
• Zhen Tong,
• Shuhua Li,
• Yanhong Yin,
• Xianbin Liu,
• Yesheng Li,
• Tongxiang Liang,
• Ziping Wu and
• Dionysios D. Dionysiou

Beilstein J. Nanotechnol. 2020, 11, 407–416, doi:10.3762/bjnano.11.31

• construction of CuO-based heterostructures (e.g., 0D/2D CuO/TiO2, 0D/3D CuO/ZnO, 2D/2D CuO/Fe2O3, 0D/2D CuO/C3N4, 2D/0D CuO/Ag3PO4) [6][12][15][16][17] and the dispersion of CuO on supporting materials (e.g., graphene, carbon nanotube) [7][18] are considered to be the most effective ways to address these

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• correlated to the active sensing film/material used. Various nanomaterial-based gas sensors have been investigated to monitor the presence of aromatic VOCs. The ones mainly studied are based on metal oxides, carbon nanotubes, graphene and hybrid materials [5][6]. Carbon nanotube based gas sensors (e.g

• ., single-wall carbon nanotube (SWCNT), multiwall carbon nanotube (MWCNT), graphene, graphene oxide (GO)) present a sensitive active layer exhibiting an electrical resistance change while in contact with the target gas due to interactions at the molecular level [7][8]. These interactions, depending whether

Facile synthesis of carbon nanotube-supported NiO//Fe₂O₃ for all-solid-state supercapacitors

• Shengming Zhang,
• Xuhui Wang,
• Yan Li,
• Xuemei Mu,
• Yaxiong Zhang,
• Jingwei Du,
• Guo Liu,
• Xiaohui Hua,
• Yingzhuo Sheng,
• Erqing Xie and
• Zhenxing Zhang

Beilstein J. Nanotechnol. 2019, 10, 1923–1932, doi:10.3762/bjnano.10.188

• carbon cloth–carbon nanotube@metal oxide (CC-CNT@MO) three-dimensional structures combine the high specific capacitance and rich redox sites of metal oxides with the large specific area and high electrical conductivity of carbon nanotubes. The prepared CC-CNT@Fe2O3 anode reaches a high capacity of 226

Hierarchically structured 3D carbon nanotube electrodes for electrocatalytic applications

• Pei Wang,
• Katarzyna Kulp and
• Michael Bron

Beilstein J. Nanotechnol. 2019, 10, 1475–1487, doi:10.3762/bjnano.10.146

Magnetic segregation effect in liquid crystals doped with carbon nanotubes

• Danil A. Petrov,
• Pavel K. Skokov,
• Alexander N. Zakhlevnykh and
• Dmitriy V. Makarov

Beilstein J. Nanotechnol. 2019, 10, 1464–1474, doi:10.3762/bjnano.10.145

• show [28][32][33][34] that in nematic liquid crystal–carbon nanotube (NLC-CNT) mixtures additionally functionalized with ferromagnetic particles, the magneto-optical response increases in comparison with pure LC. Existing theoretical models that describe NLC-CNT suspensions are related to the mean

Capillary force-induced superlattice variation atop a nanometer-wide graphene flake and its moiré origin studied by STM

• Loji K. Thomas and
• Michael Reichling

Beilstein J. Nanotechnol. 2019, 10, 804–810, doi:10.3762/bjnano.10.80

• is calculated in analogy to the energy of a collapsed carbon nanotube [17][30][49], Efold = k·a·l/2r2 where k is the curvature modulus (k = 1.4 eV for CNTs with radii smaller than 2.4 Å), a the arc length which is ≈ b = 15 nm, l the length of the curved region of 72 nm, and r the radius of curvature

Hydrophilicity and carbon chain length effects on the gas sensing properties of chemoresistive, self-assembled monolayer carbon nanotube sensors

• Juan Casanova-Cháfer,
• Carla Bittencourt and
• Eduard Llobet

Beilstein J. Nanotechnol. 2019, 10, 565–577, doi:10.3762/bjnano.10.58

• , pristine carbon nanotubes (CNTs) present some limitations for gas sensing. For example, carbon nanotube gas sensors often suffer from slow recovery, especially when operated at room temperature, which eventually results in baseline and response drift. For that reason, it is usually necessary to heat up the

• , different carbon nanotube sensors have been reported for detecting toxic pollutants emitted from vehicle exhaust [22][23], hazardous volatile organic compounds (VOCs) [24] or chemical warfare agents (CWAs) [25][26]. Usually, these modified carbon nanotubes improve the selectivity, because the chemical

• approach, carbon nanotubes act as support and charge transport transducing elements while the recognition function is performed by grafted molecules. Two examples of this have consisted of obtaining thiol-functionalized carbon nanotube buckypapers [27] or self-assembled monolayers (SAMs) of thiol molecules

Wet chemistry route for the decoration of carbon nanotubes with iron oxide nanoparticles for gas sensing

• Hussam M. Elnabawy,
• Juan Casanova-Chafer,
• Badawi Anis,
• Mostafa Fedawy,
• Mattia Scardamaglia,
• Carla Bittencourt,
• Ahmed S. G. Khalil,
• Eduard Llobet and
• Xavier Vilanova

Beilstein J. Nanotechnol. 2019, 10, 105–118, doi:10.3762/bjnano.10.10

• chemical composition of the iron oxide decorated carbon nanotube samples were investigated employing transmission electron microscopy (TEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). The differently decorated CNT samples were used to make gas sensors for detecting nitrogen dioxide. A

• as well as the effect of ambient humidity. Experimental Materials All materials and reagents used (listed below) were of analytical grade and were used as received. COOH functionalized multiwalled carbon nanotube (MWCNTs), Nanocyl (C purity higher than 95%) Nitric acid, Scharlau (HNO3 68–70

• electrical resistance against time. Nitrogen dioxide was found to strongly interact with carbon nanotube sensors, and as a result, the sensors did not fully recover their baseline resistance value during the cleaning phase, which was conducted at room temperature without heating. Applying mild heating or UV